The Blackstars line out is set at pre amp level and you can turn the Master volume right off and it does not change the line out level.
Fender Universal Asio Driver To EnableI need to use that driver to enable the use of my Fender SuperChamp x2 and Fuse to get signal into Sonar via USB.![]()
I have a Mustang III V.2 amp and will use the headphone out to record which disconnects the speaker and simulates the amp cabinet and speaker, but the line out of the amp ( low impedence) for hooking up to a mixer board or other input to amplify the amp I guess does not disconnect the speaker on that amp. I tried the USB connection and my RME Babyface is a USB connection for my sound card, and I tried all I could and when I looked at the Fender folder in Windows, the only thing it had.inf files on was Mustang I and II amps and the GEC-Dec whatever it is amp I guess is what it is. Fender Universal Asio Download Was 2Fuse does not work on my computer and I could not really decide if I needed a firmware update or not since I have V.2 of the amp and the download was 2.1 version. It really did not look as if I needed it, and besides the software would not start up. I have ASIO drivers on my RME Babyface, and will use if necessary the headphone output to record which is what that is also made for - on both amps and the other amp is not a Fender. Anyway what I read is that you can only record you can not listen to it back through the USB connection anyway, as it is not really a sound interface so you would have to use a soundcard or audiointerface and the Mustang Amp was listed in Device Manager as a Sound, Video, Game Controller Device and like I said I even disconnected my RME Babyface from USB just to try and use that Fuse software which never did work at all. I took it all back out again and never will try it, unless they actually get that software to work, and my computer is not the problem. Oh, and my RME Babyface my regular audiointerface has its own ASIO drivers and usually any manufacturer of an audiodevice with its own ASIO drivers are way better to use then ASIO4ALL and I am not sure but I do not think you can have two devices using ASIO at the same time running on the computer. Not sure about that, but that whole episode wrecked my afternoon on my computer, looking at the instructions which do not tell you that you need ASIO drivers for the USB connection anyway with Fender at all. The only thing it put in on that Mustang was USB composite device and a couple of other drivers - no ASIO drivers did I see or did Fuse put on the computer that I know of. I see some other stuff there on the Fuse Forum to look at also, but some of the instructions if Fuse does not work, I do not even have to try like the last ones on that trouble shooting page of theirs for Fuse. ![]() ASIO4ALL is basically an if all else fails, maybe this will work option. Its commonly recommended by manufacturers who dont have the capability or desire to create custom drivers. This isnt a diss on the people who created ASIO4ALL; its a pretty clever kludge, but its trying to convince Windows to do something it was never meant to do. What soundcard are you using post edited by Wookiee - 20150924 12:53:18. Primary, i7 8700K 16Gigs Ram, 3x500gb SSDs 2TB Backup HHD Saffire Pro 40. Win 10 64Bit Secondary i 7 4790K, 32GB Ram, 500Gb SSD OSProgs, 1TB Audio, 1TB Samples HHD AudioBox USB, Win 10 64Bit CbB, Adams A7xs - Event 2020s, Arturia V6, Korg Digital Legacy, Softube Modular, Arturia Keylab-88, USB-MidiSport 8x8. Fender Universal Asio Install ASIO4ALL CompletelyASIO4ALL is invasive, so if you have a piece of hardware with ASIO drivers (made for the device specifically) it is often best to uninstall ASIO4ALL completely. Realtek will function for playback, but is not great at recording. I apologize that I have not consolidated these yet, but I should as this topic comes up fairly frequently.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |